Einbau Doppelrückfahrkamera?

die ersten Sprinter (T1N)
Antworten
Benutzeravatar
JC2006
Beiträge: 11
Registriert: 02.07.2017 08:11

Einbau Doppelrückfahrkamera?

Beitrag von JC2006 » 08.07.2017 15:18

Habe mir nun für meinen JC eine Rückfahrkamera mit 2 Linsen gegönnt (LUIS RV plus). Die Kabel habe ich auf der Fahrerseite mittels eines Elektrorohres, das ich neben dem Einbau durchgeschoben habe, durchgezogen.
Aber: Wie bringe ich die Kamera an am GFK-Dach über der Tür an - da ist ja gar kein Platz, der Einbau reicht ja bis an Blech?! :oops: :shock:

Hat jemand ein Bild oder Kann erklären wie das gelöst hat? :?:

HG JC2006
James Cook 316 CDI, EZ 2006 Bj 2005
restauriert 2016, 185.000 km

Benutzeravatar
CGN
Beiträge: 401
Registriert: 04.07.2016 12:58
Wohnort: Köln

Re: Einbau Doppelrückfahrkamera??

Beitrag von CGN » 11.07.2017 07:42

Bild

Bringt dir das was?


Gesendet von iPhone mit Tapatalk
James Cook - Mercedes T1 309D
1985 Bj
Motor OM617
Automatikgetriebe

Benutzeravatar
JC2006
Beiträge: 11
Registriert: 02.07.2017 08:11

Re: Einbau Doppelrückfahrkamera??

Beitrag von JC2006 » 11.07.2017 12:49

Unbenannt.JPG
Unbenannt.JPG (32.85 KiB) 2370 mal betrachtet
OK von außen nach Innen kein Problem. Aber wie hast Du die Kabel von oben vom GFK nach unten geführt.

HG JC2006
James Cook 316 CDI, EZ 2006 Bj 2005
restauriert 2016, 185.000 km

Benutzeravatar
CGN
Beiträge: 401
Registriert: 04.07.2016 12:58
Wohnort: Köln

Re: Einbau Doppelrückfahrkamera??

Beitrag von CGN » 11.07.2017 12:57

Die Kamera wurde vom Vorbesitzer verbaut. Es ist ein Loch im Dach und das Kabel geht durch die Schränke nach vorne. Über das S-Video wird sowohl AV Signal und auch Strom für die Kamera geliefert.
Eigentlich ganz praktisch, nur blöd, da ich gerne den Röhren Monitor raus werfen würde, aber keinen passenden TFT finde...
James Cook - Mercedes T1 309D
1985 Bj
Motor OM617
Automatikgetriebe

Benutzeravatar
AndiP
Beiträge: 2622
Registriert: 25.06.2009 13:56
Wohnort: Soest

Re: Einbau Doppelrückfahrkamera??

Beitrag von AndiP » 11.07.2017 13:30

Wenn ich den Boilerkamindeckel im Hochdach sehe, ist das Unterforum wohl flasch gewählt - es handelt sich um einen Sprinter?
Beim Bremer wie CGN gesagt hat, Durchführung in Kameranähe durchs Dach, im Schrank nach unten auf den Dachholm und dort nach vorne legen.

Zum Sprinter kann ich nichts sagen.
1985er JC 309D mit 500.000km

Benutzeravatar
admin
Site Admin
Beiträge: 1455
Registriert: 04.11.2005 10:45
Wohnort: Düsseldorf

Re: Einbau Doppelrückfahrkamera??

Beitrag von admin » 11.07.2017 15:40

AndiP hat geschrieben:Unterforum wohl flasch gewählt - es handelt sich um einen Sprinter?.
... und zack, verschoben :-)
James Cook 319 CDI 7G-Tronic (Modell 2006-2012) EZ 2012 3,88t
James Cook 316 CDI Sprintshift (Modell 2000-2003) EZ 2003 3,5t
James Cook 312 D Schaltung (Modell 1995-2000) EZ 2000 3,5t

Epeg
Beiträge: 2142
Registriert: 11.07.2009 19:52
Wohnort: Im Wald hinter den Bergen

Re: Einbau Doppelrückfahrkamera??

Beitrag von Epeg » 11.07.2017 15:56

JC2006 hat geschrieben:
Der Dateianhang Unbenannt.JPG existiert nicht mehr.
OK von außen nach Innen kein Problem. Aber wie hast Du die Kabel von oben vom GFK nach unten geführt.

HG JC2006

Moin.
Kannst die Kamera nicht an die 3. Bremsleuchte schrauben und unauffällig die Kabeldurchführung hinter dieser durch das Dach bohren ??!! Habe ich auch so gemacht, meine ist zwar eine kleine unauffällige von Pioneer aber auch mit der großen von Louis sollte das gehen.

http://fotos.westfalia-freunde.de/displ ... ?pos=-1077
Dateianhänge
Rückfahrkamera an 3. Bremsleuchte
Rückfahrkamera an 3. Bremsleuchte
pioneer.jpg (36.45 KiB) 2355 mal betrachtet
Alle sagten: Das geht nicht.
Dann kam einer, der wusste das nicht und hats gemacht 8) [/b]:-)) 316CDI EZ: 03.2006. Sprintshift. 2x 80 WP Solar Modul.

SimonCook
Beiträge: 56
Registriert: 16.09.2018 08:12
Wohnort: Karlsruhe

Re: Einbau Doppelrückfahrkamera??

Beitrag von SimonCook » 12.03.2019 16:04

Hallo zusammen,

Kann mir hier jemand erklären, wie und wo genau ich die Kabel verlegen muss bzw. welche Erfahrungen ihr gemacht habt, wo die Kabel gut verlegt werden können?

Ab 01. April haben wir unseren 2004er James Cook endlich bei uns. Im November gekauft und seither steht er in einer Halle. Ich habe also noch keine praktischen Erfahrungen mit dem Guten.

Vielleicht gibt es ja jemanden, der/die mir beschreiben kann (ggf mit Bildern), wie ich vorgehen muss. Muss ich die Küche oder weiter vorne Seitenverkleidung abbauen oder kann man die Kabel auch so bis ins Cockpit verlegen?

Zum einen geht es um Kabel von der Rückfahrkamera bis zum Amaturenbrett, zum anderen um die Kabel einer Solaranlage zur Batterie (aber das wäre wohl ein anderes Thema).

Ich wäre euch auf jeden Fall sehr dankbar, wenn ihr mir im Vorfeld behilflich sein könntet.

Beste Grüße
Simon
James Cook, 316 CDI, Schaltgetriebe, EZ 2004, ATM bei 231tkm

OldWest
Beiträge: 176
Registriert: 15.12.2013 16:25

Re: Einbau Doppelrückfahrkamera??

Beitrag von OldWest » 12.03.2019 19:12

Rear Camera System

A. Camera

If the camera is small, it can be mounted on the fiberglass top third brake light. The wiring then goes through the same hole as the third brake light.

If the camera is larger, then the camera bracket is screwed (or 3M VHB double sided taped) to the fiberglass top just below the third brake light. Depending on the bracket, a through hole for the cable is drilled through the fiberglass top (behind the bracket or to the side of the bracket). The cable would go through a grommet in the hole to seal any water out.

B. Camera Cable Routing

Once the cable is inserted through the fiberglass top from the outside, it should dangle inside the Sprinter and be fishable from inside. No cabinets or walls need to be removed. The fiberglass top in the rear above the rear door is one layer and does not have an interior roof liner. The back Westfalia panel wall does not reach the top of the fiberglass roof so the cable can rest on top that wall or be clipped.

The cable runs along the top of the Westfalia back panel wall, then drops down vertically to the driver side taillight (USA).

If there is no hole in the floor below the taillight, make one and use a grommet.

The cable is then run through the Sprinter body floor, then tied to othee wiring/cables under the van, all the way to the engine compartment.

In the engine compartment, there is a hole through the bulkhead where the gas and brake pedals are. The cable runs through the engjne compartment bulkhead into the area below the dashboard.

C. Distribution Box

The distribution box can be mounted somewhere under the dashboard (screwed or glued to the bulkhead near the hood release or the underside of the dashboard).

The camera cable goes into the distribution box.

D. Power

Power for the distribution box can come fromi the fusebox under the steering wheel. You can use a piggyback add a circuit fuse to replace one of the existing fuses (forgot which fuse) to power the distribution box.

E. Monitor

The monitor can sit on the dashboard or be mounted where the rear view mirror should normally be (top of windshield between the visors).

The monitor cable is run from the distribution box, then upwards between the front door.and dashboard, then between dashboard and A pillar, then to monitor.

F. Auto On When in Reverse

Many rear view monitor (and camera) will turn on when the transmission is placed in reverse. As the installer could not figure out which wire to use, they a wire from the rear taillight reverse back up light to the distribution box (tied to the camera cable).

As I always turn the monitor on and leave on when driving, this step could be skipped.
2005 NAFTA (USA) Airstream Westfalia (2004 Dodge Sprinter) Version of James Cook

OldWest
Beiträge: 176
Registriert: 15.12.2013 16:25

Re: Einbau Doppelrückfahrkamera??

Beitrag von OldWest » 15.03.2019 23:27

some photos of my solution
Dateianhänge
Monitor cable and monitor
Monitor cable and monitor
20190315_143917.jpg (2.85 MiB) 1340 mal betrachtet
Monitor cable near A pillar
Monitor cable near A pillar
20190315_143924.jpg (2.18 MiB) 1340 mal betrachtet
Monitor.cable running along dashboard
Monitor.cable running along dashboard
20190315_145328.jpg (3.08 MiB) 1340 mal betrachtet
Power to box from add-a-circuit piggyback fuse under steering wheel
Power to box from add-a-circuit piggyback fuse under steering wheel
20190315_145350.jpg (3.07 MiB) 1340 mal betrachtet
Distribution box mounted near parking brake release
Distribution box mounted near parking brake release
20190315_145317.jpg (2.54 MiB) 1340 mal betrachtet
Camera cable going through floor to underneath van
Camera cable going through floor to underneath van
20190315_145905.jpg (2.63 MiB) 1340 mal betrachtet
Camera system reverse wire connected to taillight
Camera system reverse wire connected to taillight
20190315_145850.jpg (1.59 MiB) 1340 mal betrachtet
Top of back wall where camera cable can rest
Top of back wall where camera cable can rest
20190315_145918.jpg (2.07 MiB) 1340 mal betrachtet
Camera with cable going through grommet
Camera with cable going through grommet
20190315_145930.jpg (2.62 MiB) 1340 mal betrachtet
2005 NAFTA (USA) Airstream Westfalia (2004 Dodge Sprinter) Version of James Cook

Antworten

Zurück zu „James Cook Generation 2 (1995-2006)“