Remove B pillar trim

die ersten Sprinter (T1N)
Antworten
Adrianlle
Beiträge: 322
Registriert: 17.09.2015 11:56

Remove B pillar trim

Beitrag von Adrianlle » 23.03.2018 11:00

Greetings from the UK. I am installing an electric sliding step ( Thule omnistep) and would like to fit the in/out switch on the B pillar trim behind the passenger seat. Can anybody tell me how to remove that please?

Also I would like to wire the step so that it also retracts automatically when the engine is started. There is a Thule kit for that which uses a relay and a capacitor. It looks as if the electrical feed comes from the ignition switch. Can anyone suggest please the best place to get the 12v feed for this so that as the engine is started the relay is energised to retract the step ?

Thank you. Adrian.

Epeg
Beiträge: 2142
Registriert: 11.07.2009 19:52
Wohnort: Im Wald hinter den Bergen

Re: Remove B pillar trim

Beitrag von Epeg » 23.03.2018 22:49

Hallo.
Du musst den Sicherheitsgurt unten abschrauben.
Dann die Türdichtungen abziehen. Nun kannst du die Verkleidung vorziehen. Das Plastik der Trittstufe drückst du etwas mit einem Kunststoffkeil zur Seite.
Wenn das nicht geht, muss der Beifahrersitz und die Trittstufe ausgebaut werden.

Vorsicht am Sicherheitsgurt oben. Die Halterung ist nur gesteckt !!!!!!!!. Auf keinen Fall das Kabel vom Gurtstraffer abziehen !!

Das Relais und den Kondensator habe ich auch an 12 Volt Zündplus geklemmt.
Alle sagten: Das geht nicht.
Dann kam einer, der wusste das nicht und hats gemacht 8) [/b]:-)) 316CDI EZ: 03.2006. Sprintshift. 2x 80 WP Solar Modul.

Adrianlle
Beiträge: 322
Registriert: 17.09.2015 11:56

Re: Remove B pillar trim

Beitrag von Adrianlle » 24.03.2018 17:00

Thank you Epeg. Can you remember where exactly you took your ignition feed from - for the relay.? Adrian

Epeg
Beiträge: 2142
Registriert: 11.07.2009 19:52
Wohnort: Im Wald hinter den Bergen

Re: Remove B pillar trim

Beitrag von Epeg » 25.03.2018 15:09

Die Trittstufe habe ich direkt an das Mercedes Bordnetz angeschlossen. Also Dauerplus Kl.30 und Zündpluss Kl.15. Diese findest du im Kasten unter dem Fahrersitz.
Alle sagten: Das geht nicht.
Dann kam einer, der wusste das nicht und hats gemacht 8) [/b]:-)) 316CDI EZ: 03.2006. Sprintshift. 2x 80 WP Solar Modul.

Adrianlle
Beiträge: 322
Registriert: 17.09.2015 11:56

Re: Remove B pillar trim

Beitrag von Adrianlle » 25.03.2018 20:50

Thank you Epeg.

Epeg
Beiträge: 2142
Registriert: 11.07.2009 19:52
Wohnort: Im Wald hinter den Bergen

Re: Remove B pillar trim

Beitrag von Epeg » 26.03.2018 21:15

Adrianlle hat geschrieben:
25.03.2018 20:50
Thank you Epeg.
Vergess nicht eine Sicherung einzubauen, falls die Stufe mal klemmt
Alle sagten: Das geht nicht.
Dann kam einer, der wusste das nicht und hats gemacht 8) [/b]:-)) 316CDI EZ: 03.2006. Sprintshift. 2x 80 WP Solar Modul.

Adrianlle
Beiträge: 322
Registriert: 17.09.2015 11:56

Re: Remove B pillar trim

Beitrag von Adrianlle » 05.04.2018 17:38

I have now removed enough of the b pillar trim to look behind it. There is not that much clearance. I will need to drill a 48mm hole in the trim itself for the switch but wonder if I will also need to drill such a hole as well in the metal b pillar. If so then where to drill? To ensure that there is enough clearance behind the switch for the cable terminals. Can Epeg or anyone else help please. Thank you. Adrian

Epeg
Beiträge: 2142
Registriert: 11.07.2009 19:52
Wohnort: Im Wald hinter den Bergen

Re: Remove B pillar trim

Beitrag von Epeg » 05.04.2018 21:10

Hallo Adrian.
Ich mache morgen ein Foto von dem Montageort und dem Schalter der Omnistep.
Alle sagten: Das geht nicht.
Dann kam einer, der wusste das nicht und hats gemacht 8) [/b]:-)) 316CDI EZ: 03.2006. Sprintshift. 2x 80 WP Solar Modul.

Epeg
Beiträge: 2142
Registriert: 11.07.2009 19:52
Wohnort: Im Wald hinter den Bergen

Remove B pillar trim

Beitrag von Epeg » 06.04.2018 07:26

Hier die Bilder vom Schalter.

Der Montageort vom Schalter sollte soweit wie möglich am Rand (nach Innen) der Verkleidung sein. Dort ist am meisten Platz.

Du hast wahrscheinlich einen runden Schalter ??? 48mm ist zu groß. Das wird sehr eng werden. . Kauf dir einen kleineren Schalter.
Dateianhänge
Schalter Omnistep Einbautiefe
Schalter Omnistep Einbautiefe
20180406_070829.jpg (1.41 MiB) 1367 mal betrachtet
Schalter Omnistep
Schalter Omnistep
20180406_070536.jpg (1.87 MiB) 1368 mal betrachtet
Schalter Omnistep von unten gemessen.
Schalter Omnistep von unten gemessen.
20180406_070606.jpg (1.9 MiB) 1368 mal betrachtet
Alle sagten: Das geht nicht.
Dann kam einer, der wusste das nicht und hats gemacht 8) [/b]:-)) 316CDI EZ: 03.2006. Sprintshift. 2x 80 WP Solar Modul.

Adrianlle
Beiträge: 322
Registriert: 17.09.2015 11:56

Remove B pillar trim

Beitrag von Adrianlle » 07.04.2018 13:55

Thanks Epeg. My switch -omnistep - is round and will be too big. So I need to find a switch like yours. I can never remember the difference between soft, dpdt, momentary etc. So could you treat me like an electrical idiot and tell me what sort of rocker switch I need? I will be using relay to retract the step when the ignition is switched on and will wire in a capacitor to that circuit to ensure the step fully retracts.
What would I do without this forum - despite the language difficulties for me! Thanks.

Epeg
Beiträge: 2142
Registriert: 11.07.2009 19:52
Wohnort: Im Wald hinter den Bergen

Re: Remove B pillar trim

Beitrag von Epeg » 07.04.2018 16:04

Es ist ein Taster 4. Polig ?? Schließend. Wie man ihn nennt weiß ich leider nicht. Aber hier im Forum gibt es Elektroprofis die es bestimmt wissen.
Alle sagten: Das geht nicht.
Dann kam einer, der wusste das nicht und hats gemacht 8) [/b]:-)) 316CDI EZ: 03.2006. Sprintshift. 2x 80 WP Solar Modul.

Adrianlle
Beiträge: 322
Registriert: 17.09.2015 11:56

Re: Remove B pillar trim

Beitrag von Adrianlle » 07.04.2018 20:07

Thanks Epeg. I have done some research since your email and I think a double changeover switch for a Project 2000 electric step should work. The photos of it look v similar to your own switch. So I have ordered one of those and will post in the forum if it works ok. Thank you. Adrian

Antworten

Zurück zu „James Cook Generation 2 (1995-2006)“