Infos zu Sherpa Translift gesucht (NCV3)

die zweite Generaton Sprinter (NCV3)
Antworten
rainerd
Beiträge: 396
Registriert: 28.12.2018 18:57

Infos zu Sherpa Translift gesucht (NCV3)

Beitrag von rainerd » 24.05.2019 20:37

Moin Forum,
ich finde keinerlei Infos ob der Sherpa Translift auch standardmäßig beim NCV3 möglich ist. Ich habe das auch noch nie bei einem gesehen. Wäre hier über Infos und Teilenummern (falls anders als beim T1N) sehr dankbar.
Viele Grüße,
Rainer

rainerd
Beiträge: 396
Registriert: 28.12.2018 18:57

Re: Infos zu Sherpa Translift gesucht (NCV3)

Beitrag von rainerd » 27.05.2019 19:29

schade, keiner ne Idee? Dann versuche ich es doch mal beim MB Händler

rainerd
Beiträge: 396
Registriert: 28.12.2018 18:57

Re: Infos zu Sherpa Translift gesucht (NCV3)

Beitrag von rainerd » 11.06.2019 19:24

Bin etwas weiter gekommen. Die Teilenummer war einmal 282003248055 und laut Westfalia wurde die Produktion wegen geringer Nachfrage eingestellt. Mir ist immer noch ein Rätsel wie der montier wird, falls da doch jemand Infos oder Bilder hat, gerne her damit.

rainerd
Beiträge: 396
Registriert: 28.12.2018 18:57

Re: Infos zu Sherpa Translift gesucht (NCV3)

Beitrag von rainerd » 12.06.2019 12:42

Falls es für andere auch von Interesse ist, ich bin inzwischen an eine Montageanleitung für den NCV3 gekommen. Das hilft sehr viel weiter. Ich denke man kommt mit einen Translift für ein anderes Model auch hin, allerdings bleiben die Befestigungen der Knackpunkt. Vielleicht hat ja hier jemand eine Idee wie man da rankommt.

Montageanleitung anbei.
Dateianhänge
MA_Sportgerätehalter_2011_04_15_einseitig.pdf
(1.02 MiB) 126-mal heruntergeladen

rainerd
Beiträge: 396
Registriert: 28.12.2018 18:57

Re: Infos zu Sherpa Translift gesucht (NCV3)

Beitrag von rainerd » 31.07.2019 08:29

Hier ein Bild wie es am Ende am NCV3 aussieht. Ich habe allerdings oben noch eine zweite Querstange montiert, um in der Mitte eine dritte Stange samt Halter montieren zu können. Dadurch kann ich auch kürzere Boards mitnehmen. Die oberen Teile der Halter habe ich inzwischen entfernt. Durch die Biegung liegt das Board ganz komisch drin und ein zweites wäre schwierig. Ohne ist es einfach plan an der Querstange oben und lässt sich leichter befestigen (siehe zweites Bild).
IMG_20190727_110921.jpg
IMG_20190727_110921.jpg (3.84 MiB) 1403 mal betrachtet
IMG_20190727_165610.jpg
IMG_20190727_165610.jpg (3.98 MiB) 1403 mal betrachtet

Vtxbe
Beiträge: 259
Registriert: 18.09.2016 07:49
Wohnort: Belgium

Re: Infos zu Sherpa Translift gesucht (NCV3)

Beitrag von Vtxbe » 04.08.2019 21:01

Hi Rainerd,

I'm windsurfer and have interest with your translift.

What do you think about water ingresses near the screw ?

Increases the overall wide because of the sherpa and the board ?

How many board do you transport ?

What about mast, sails and boom ?

Where do you find a sherpa ?

Have good wind.

PS do you travel to Brouwersdam ( Netherland ) I enjoy to have a look on your translift.

rainerd
Beiträge: 396
Registriert: 28.12.2018 18:57

Re: Infos zu Sherpa Translift gesucht (NCV3)

Beitrag von rainerd » 05.08.2019 08:37

Vtxbe hat geschrieben:
04.08.2019 21:01
What do you think about water ingresses near the screw ?
Both, the insert and the screws are sealed and it was mounted by a professional. I don't expect water to become an issue as there is also no real water pressure on it.
Vtxbe hat geschrieben:
04.08.2019 21:01
Increases the overall wide because of the sherpa and the board?
Depends on the mounted position of the rack on the plates. You can move the base bars up and down. The lower it gets, the wider it gets obviously. Mine was adjusted that the car height will not increase. The overall width is not wider than the mirror. The wind noise is awful, but I fixed it by putting something (for now a towel, better solution tbd.) between the front rack and the roof, that was causing most noise.

Vtxbe hat geschrieben:
04.08.2019 21:01
How many board do you transport ?
I transported so far only one waveboard but I am a kitesurfer and I want to carry 1 waveboard (big minimalibu) plus 2 shorter kitewaveboards. I bought a big windsurfbag for that to also put some wet gear in it. Im general think the sherpa will fit 2 windsurfboards in your case.
Vtxbe hat geschrieben:
04.08.2019 21:01
What about mast, sails and boom ?
Sherpa offers a mast holder, you could also put a bag on it with all the gear inside, depending on the weight and size. In theory you could mount a sherpa on both sides of the car.
Vtxbe hat geschrieben:
04.08.2019 21:01
Where do you find a sherpa ?
I got mine used on eBay Kleinanzeigen.
Vtxbe hat geschrieben:
04.08.2019 21:01
PS do you travel to Brouwersdam ( Netherland ) I enjoy to have a look on your translift.
Never been there, but on my list, I'll keep you in mind :)

Feel free to get in touch with more questions,
Rainer

Vtxbe
Beiträge: 259
Registriert: 18.09.2016 07:49
Wohnort: Belgium

Re: Infos zu Sherpa Translift gesucht (NCV3)

Beitrag von Vtxbe » 06.08.2019 20:55

vielen dank, Rainer.

tschuss.

Vincent

Antworten

Zurück zu „James Cook Generation 3 (2006-2012)“