Rust - Wiper Posts

die ersten Sprinter (T1N)
Antworten
Benutzeravatar
Westy512
Beiträge: 4
Registriert: 23.09.2013 19:38

Rust - Wiper Posts

Beitrag von Westy512 » 23.09.2013 20:34

I noticed some rust around the wiper attachment nuts and washers so the weekend turned into a bit of a repair time which was perfect since the weather had just changed and it was beautiful outside

After removing, noticed the beginnings of some slight rusting under the washers. Taped it off, and used the same paint I used on the Air Tabs which was such a good match. A bit of careful light sanding and painting up the washer and nut, and hopefully this will last a bit longer.

[images wiper1.jpg wiper2.jpg wiper3.jpg wiper4.JPG wiper5.jpg not online any more]

Benutzeravatar
Westy512
Beiträge: 4
Registriert: 23.09.2013 19:38

Re: Rust - Wiper Posts

Beitrag von Westy512 » 23.09.2013 20:37

Here is the finished product.

[images wiper6.jpg wiper7.JPG not online any more]

Epeg
Beiträge: 2141
Registriert: 11.07.2009 19:52
Wohnort: Im Wald hinter den Bergen

Re: Rust - Wiper Posts

Beitrag von Epeg » 23.09.2013 21:32

Hallo David,
Du hast Glück, dass es nur unter den Scheibenwischern ein bischen rostet. Schlimmer ist der Rost unter der Windschutzscheibe :(


Hello David,
You're lucky that it rusts a little just under the windshield wipers. Even worse is the corrosion under the windshield :(
Alle sagten: Das geht nicht.
Dann kam einer, der wusste das nicht und hats gemacht 8) [/b]:-)) 316CDI EZ: 03.2006. Sprintshift. 2x 80 WP Solar Modul.

Epeg
Beiträge: 2141
Registriert: 11.07.2009 19:52
Wohnort: Im Wald hinter den Bergen

Re: Rust - Wiper Posts

Beitrag von Epeg » 24.09.2013 19:11

Rust Front Window

[image 2013-09-24 19.13.44.jpg not online any more]
Alle sagten: Das geht nicht.
Dann kam einer, der wusste das nicht und hats gemacht 8) [/b]:-)) 316CDI EZ: 03.2006. Sprintshift. 2x 80 WP Solar Modul.

Benutzeravatar
endeavour
Beiträge: 319
Registriert: 26.04.2012 08:52

Re: Rust - Wiper Posts

Beitrag von endeavour » 02.03.2015 18:57

Hi,

ich hol' den Thread mal wieder hoch, nach dem bei mir diese Mutter und Unterlegscheibe so aussieht
[Bild DSCI1114.JPG leider nicht mehr online]
drum habe ich mir die neu besorgt
[Bild DSCI0788.JPG leider nicht mehr online]
habe diese dann für kleines Geld galvanisch verzinken lassen, nun ist da erst mal Schluss mit Rost

Gruß
endeavour

[Bild DSCI1113.JPG leider nicht mehr online]
Reiselust heilt Rentnerfrust :-)Bild
James Cook 316 CDI Automatik (Modell 2000-2003) EZ 2/2004 (weiße Einrichtung)

Antworten

Zurück zu „James Cook Generation 2 (1995-2006)“