James Cook Forum

Hello,

I got some additional pictures from the seller:

Thanks a lot for the infos and the picture!

I think I'm going to order a repair panel kit (https://easyparts.online/mercedes-t1-se ... -panels-12).

Hello Andi, Thanks a lot for your answer. Actually I had also found this website in Poland and was thinking about ordering from them. They told me the iron is approximatively 1mm thick, and galvanized, with is surprising. Would you eventually mesure the thickness of the part you got from them and up...

Hello,

I'm looking for some iron panels to restore my James Cook 210D, which has some rust.

Has somebody here already ordered from this site in Poland? https://easyparts.online/for-Mercedes-B ... rrency=EUR

Or any experience with Van Wezel or Diederichs panels ?

Thanks a lot !

Hello,

I replaced the theshower faucet by the good looking "NIMBUS TF21W Shower Mixer Tap".
Now it has a strange behaviour, when I open the faucet in the kitchen, water comes also out in the bathroom !


Any ideas...? Thanks !

Hello, I installed the inox exhaust line. The parts needed : • 1m straight tube • 1x over axle bend • 2x 60° bend • 55cm straight tube • 4 brackets • 1 suspension 1 - Ligne complète en pièces.jpg 2 - Angle coudes 60°.jpg 3 - Sortie.jpg I had to cut the first straight tube, which was soldered by the ...

Thanks a lot for the pictures, nice work ! Thomas, I searched for websites in the UK but didn't find any Mercedes A6014901921 part available. Pot d'échappement Mercedes A6014901921.png So, I ordered some inox parts, I hope it will fit. I'm not sure about the angles of the bends, so I took different ...

Lutz, another problem is that if the exhaust line goes straight (after the middle part), it will encounter the spare wheel... Maybe if I add two 60°bend parts, it will be OK. This would shift the line by approximatively 20 cm (23-24cm would be perfect). I'm afraid two 90° bends would be too much for...

Hi Lutz, thanks a lot for the infos. Their part are a little bit more expensive than on the French site, but the interesting thing is that their over axle bend is a lot higher (18,5cm, against 13,5), like it is originally on the Mercedes : https://www.csp-shop.com/en/exhaust-heating/over-axle-bend-2...

Yes, the exhaust exits I saw are always being the rear wheel. Sometimes on the side, sometimes straight to the back of the van. I found some interesting parts on a French website (see below). The second part seems to only exist in 51mm diameter (I guess it's actually 50,8). Would this fit with the r...

OK, thanks.
Would it be possible to see a picture of your exhaust line ? I see that some James Cook models have the exit on the rear, and others on the side...

Hallo

Ich bin freudiger Besitzer eines James Cook 210D T1 von 1992.
Würde mich auch sehr über den Leitfaden freuen.

gretschmaarten@gmail.com

Danke, viele Grüße !

Hi Andi,

Thanks a lot for your reply. I'll construct the exhaust line with different parts.

Have you already done it yourself ? Maybe you have some pictures ?

Thinking about using inox tubes, they are more expensive but will last longer.

Hello !

I need to change the exhaust pipe on my 1992 210D James Cook.
Does someone know were I can find it ? The shape seems quite unusual and hard to find.

Thanks !

Hello, As my upper part was broken, I also ordered a "rollo-clipse" here : https://www.camping-kaufhaus.com/hartal-dachhaube-ersatzverschluss-weiss-206-086-und-080/a-23845/ 1-2-Attaches.jpg I just had to make a small 3mm + 7mm hole for the screw : 2-2-Trous.jpg And then cut a little part of the plas...